Mall redevelopment: can you test a parking lot in GenAnywhere?
Yes, at the level of form and space. Here is what a parking test can show, and what it still needs from a parking study.
You can test a parking lot in GenAnywhere as a layout question rather than a demand question. Put the store, the lot, the aisles, and a redevelopment block into one model, and you can see how much parking survives when a building takes part of the site. The test shows form, access, and trade-offs. It does not count cars or replace a parking study.

1 Frame the parking question as a form question
Most mall redevelopment arguments start with a number: how many spaces will be lost. That number matters, but it is the end of the conversation, not the start. Before anyone counts, the team has to agree on what replaces the lot and how the remaining parking works. A model makes that opening step visible, because the shape of the site answers half the question before anyone opens a spreadsheet.
1.1 Separate surface parking from structured parking
Surface parking is cheap and land-hungry. Structured parking is expensive and compact, and it changes the street edge. When you test a redevelopment, decide which kind of parking the option assumes. A scheme that replaces a surface row with a podium garage uses the land very differently from one that keeps the row and builds on the far side of the site.
1.2 Decide what the test is meant to show
A parking test can answer several questions: how much land the store keeps, how visitors reach the door, how service vehicles move, and what the street looks like from the sidewalk. Pick the questions before you build the model, or the view will drift. Each question leads to a different camera and a different comparison.
2 Map the lot as it exists
The current condition is the reference for every option. Map the store, the lot, the ring road, and the entries as they are, and keep that version separate from the experiments. Teams that skip this step end up arguing about a baseline nobody can see.
2.1 Keep the store and the lot in one model
Buildings and parking behave as a pair on a retail site. The store entrance pulls cars to one side of the lot, and the loading dock pulls trucks to another. Model both, with the aisles between them. A model that shows the store alone hides the circulation that makes the site work or fail.
2.2 Mark entries, aisles, and islands
Note where cars enter, how the aisles run, and where the planted islands sit. These details explain why the lot feels the way it does. A lot with long straight aisles reads differently from one with a loop. In the model, the aisle pattern also shows where a new building could sit without cutting the loop. That sounds like a small detail until a scheme blocks the loop and the whole lot has to be reconfigured around a route nobody planned for.

3 Test a smaller footprint
The common redevelopment move is to take part of the lot for a new building. The test is whether the remaining parking still works. That question has a spatial answer, even before anyone counts spaces, because circulation can fail long before capacity does.
3.1 Fill part of the lot with a building block
Place a block where the new building would go and look at what it covers. The lost parking is visible, and so is the new edge along the remaining lot. If the block cuts the main aisle, the whole lot reorganizes around it. That reorganization is the real cost of the scheme, and it appears in the model immediately.
3.2 Check the remaining circulation
Follow a car from the street to the store door after the block is placed. If the route now doubles back or crosses a service lane, the scheme has a problem that a space count would miss. Note the pinch points and the places where pedestrians and cars share space. Those are the spots to fix before the option goes to a public meeting.
4 Compare structured and surface options
A structured option changes the economics and the street. It frees ground for buildings, but it also creates a wall where the lot used to be open. Comparing the two options in the same model helps a team see that trade-off without pretending to settle it.
4.1 Stack parking and free the ground
Replace part of the surface lot with a parking structure block and put a building on the freed land. The model shows how much ground the structure releases and how tall it has to be. Keep the block simple. At this stage, the question is whether the massing fits beside the store, not how the decks will be laid out inside.

4.2 Look at the edges from the street
Walk the street edge in the model and compare the options. A surface lot presents a wide opening with cars and lights. A structure presents a facade, which can be better or worse depending on how it meets the sidewalk. A structure with active frontage at the ground level behaves very differently from a blank wall of ventilation grilles. The Urban Land Institute's work on retail and mixed-use development is useful background when the discussion turns to how parking structures change the street.
5 State what the test cannot settle
The model is a spatial test. Parking demand, shared-parking agreements, and the local parking requirement are separate questions with their own methods. A good test makes those questions clearer. A bad test pretends to answer them.
5.1 Parking demand is a study, not a model
How many cars arrive on a Saturday afternoon depends on the store mix, the trade area, and the way people travel. None of that is in a site model. Use the model to show how the site performs under a given assumption, and let the parking study supply the assumption. That division keeps both tools honest. When the two disagree, the disagreement is usually about the assumption rather than the layout, and that is a productive place to start.
5.2 Check the local rules and access standards
Parking minimums, maximums, and access standards vary by place and change over time. Confirm the current rules with the local planning office before a scheme is presented. The model can show a layout that meets a rule, but it cannot tell you what the rule is. Write the rule version into the option notes so the comparison stays current.
6 Test a parking layout in GenAnywhere
GenAnywhere builds an editable 3D site model from a mapped area using satellite and map data. It identifies building footprints, estimates heights, infers building types, and includes the surrounding vegetation, with buildings, terrain, vegetation, and water as separate layers. You can replace a building, move or rotate it, change its height or type, and export a GLB for 3D, BIM, GIS, and game engine workflows. The model is initial site context. It does not count parking demand, and it does not replace a traffic or parking study.
6.1 Build the current condition
Select the mall site and a margin that includes the surrounding streets, then generate the model. Check the store footprint, the lot, and the access points against a recent aerial image or a site visit. Small changes on the ground, such as a new pad site or a closed entry, can make the baseline wrong, and a wrong baseline undermines every option that follows.
6.2 Try a second option on a copy
Duplicate the site and place a building block on part of the lot. Compare the two views with a fixed camera, then move the block to a second position and compare again. Keep each option as its own copy so the meeting can move between them. Name the files by option and date, because a mall scheme usually goes through several rounds.
6.3 Export both options for comparison
Export the options as GLB and bring them into the tool the team uses for review. Add a note that lists the parking assumption used in each option, the rule version, and the open questions. The export carries a permanent commercial license, though the original files cannot be resold or used for AI training. Third-party data inside the model may have its own terms.
See how the site model workflow fits a review
7 FAQ
FAQ-1 Can GenAnywhere count parking spaces?
Not from the generated model alone. The model shows the lot, the aisles, and the building footprints, and you can see how much land each option uses. Counting spaces needs a layout with striping and dimensions, which comes from a design tool or a parking study. Use the model to test the arrangement, then count in the layout that follows.
FAQ-2 What if the mall is still operating during redevelopment?
Model the store as it operates now, then test the phasing in copies. Move the new building block in stages and check that the open lot still reaches the entrances. Keep the service route clear in each stage. A phasing test in the model will not solve every operational question, but it shows which stages squeeze the site hardest.
FAQ-3 How many options should I compare?
Two or three options are usually enough to see the trade-offs. More than that and the meeting spends its time navigating files instead of discussing the scheme. Compare a surface option, a structured option, and a hybrid if the site supports one. Keep the camera and the assumptions the same across all of them.
FAQ-4 Does the model show parking demand?
No. Demand depends on the store mix, the trade area, and travel behavior, and those belong to a parking study. The model shows how a given amount of parking is arranged on the site and how the arrangement changes when a building is added. Pair the model with the study and the local rules, and the numbers and the layout can be discussed together.
Content and technical notes
This article was prepared by the GenAnywhere team with AI-assisted drafting and human review.
Product features, formats, and availability change as the platform evolves; refer to the official GenAnywhere website for current details.
For technical questions or corrections, contact support@genanywhere.com.
Last reviewed: 2026-11-20.